40Gbps 8K Fiber Optic Extender Kit
- VendorAVPro Edge
40Gbps 8K Fiber Optic Extender Kit
- VendorAVPro Edge
Multi-mode OM2/3/4 Compatible: The AC-EXO-KIT may be used with all classifications of multi-mode fiber. Total distance varies per classification. Using a 40Gbps, 8K/60Hz 4:2:0 signal, the following distances have been confirmed: OM2 / 40 meters, OM3 / 200 meters, OM4 / 300 meters.
Long Distance Transmission: HDMI signals may be extended up to 300 meters using OM4 multi-mode fiber, safely delivering content with zero loss of fidelity in the most challenging installations.
HDMI 2.1 Features: Auto Low Latency, Variable Refresh Rate, HDR10 and Dynamic HDR formats including Dolby Vision, HDR10+ and HLG, Quick Frame Transport and Source Based Tone Mapping. 8K/60 4:2:0, High Frame Rate 4K/120fps capable.
Near-Zero Latency: Latency is less than 8 microseconds, measurable but visually imperceptible.
Dual HDMI Output: The AC-EXO-KIT receiver features two HDMI outputs, with HDMI 1 full-bandwidth passthrough and HDMI 2 an always scaled output. Scaling can be selected to be 8K to 4K, 8K to 1080p, and 4K to 1080p.
Comprehensive EDID Management: Today’s leading-edge NextGen systems must now contend with mixed resolutions of 8K, 4K and in application-specific circumstances legacy HD displays, with the potential for EDID conflicts ever-present. The AC-EXO-KIT is equipped with a robust EDID management system that enables juggling video resolutions and audio codec combinations for EDIDs that provide a congenial match for reliable system operation.
An EDID Copy function allows for acute copying and saving of known, working EDIDs, for stable kit operation and HDCP repeatability.
Onboard Troubleshooting: Leave your Fox & Hound test kit behind in the shop? The AC-EXO-KIT has you covered. Where required, the transmitter can generate a 1080p or 4K test pattern to aid with fiber verification, connected device configuration settings, or source viability.
Control Options: Configurable, bidirectional management for IR & RS-232 signals provides a carefully nuanced added plus to the AC-EXO-KIT, consolidating wiring to a solitary pull and mitigating the use of supplemental devices for a clean, efficient installation. Simplified control requirements can take advantage of the AC-EXO-KIT’s I-PASS, forwarding commands directly from a control system IR-out port into the TX unit I-PASS input, proceeding to the receiving end and routing directly from the RX unit’s IR-out into the display’s IR input jack (if equipped) or through an attached supplied IR emitter. ESD (electrostatic discharge) protection adds a welcomed layer of defense for all connected products.
| Video | |
| Video Resolution | Up to 8K 60 Hz 4:2:0 / 8K 30 Hz 4:4:4 / 4K 120 Hz |
| HDR Formats | HDR10, HDR10+, Dolby Vision, HLG |
| Color Space | YUV (Component), RGB (CSC: REC.601, REC.709, BT2020, DCI, P3 D6500) |
| Chroma Subsampling | 4:4:4, 4:2:2, 4:2:0 |
| Color Bit Depth | Up to 16-bit (1080p), up to 12-bit (4K) |
| Scaling | Output 2 Only: 8K to 4K, 8K to 2K (1080p) |
| Audio | |
| Audio Formats Supported HDMI | PCM 2.0-Ch., LPCM 5.1 & 7.1, Dolby Digital, DTS 5.1, Dolby Digital Plus, Dolby TrueHD, DTS-HD Master Audio, DTS:X, Dolby Atmos |
| Fiber | |
| Type | Multimode OM3 |
| Connector Type | Simplex LC (Lucent Connector) |
| Recommended Fiber | OM3 Cleerline SFF™ Fiber |
| Distance | |
| OM2 | Up to 40 m |
| OM3 | Up to 200 m |
| OM4 | Up to 300 m |
| HDMI Cable Distance (Passive) | 40 Gbps: Up to 4 m (using Bullet Train © Ultra High Speed HDMI cable) |
| HDMI Cable Distance (AOC) | 40 Gbps: Up to 100 m (using Bullet Train © Ultra High Speed HDMI cable) |
| Other | |
| Bandwidth | 40 Gbps (FRL5) |
| HDCP / Copy Protection | HDCP 2.3 and earlier |
| Ports | |
| HDMI | TX and RX: Type-A |
| IR Transmit | TX and RX: 3.5 mm Mono Jack (TS) |
| IR Receive | TX and RX: 3.5 mm Stereo Jack (TRS) |
| RS-232 | TX and RX: 3-pin Terminal Block |
| Power | TX and RX: 2-pin Terminal Block, USB-C |
| Environmental | |
| Operating Temperature | 23 to 125 °F (-5 to 51 °C) |
| Storage Temperature | -4 to 140 °F (-20 to 60 °C) |
| Operating Humidity | 5% to 90% RH, non-condensing |
| Power | |
| Power Consumption | Total: 2.5 W max |
| Power Supply | Input: 48 V 0.5 A Output: DC 5 V 1 A |
| Physical | |
| Dimensions (Unit) | TX and RX are same: W × D × H: 140 × 15.4 × 80.6 mm (5.5 × 0.6 × 3 in.) |
| Dimensions (Packaged) | Kit: W × D × H: 194 × 84 × 135 mm (7.6 × 3.3 × 5.3 in.) |
| Weight (Unit) | TX or RX each alone: 0.55 lb. (0.25 kg) |
| Weight (Packaged) | 2.5 lb. (1.13 kg) |
| Notes | *Specifications are subject to change without notice. Mass and dimensions are approximate. |
